-
-
Specifications:
Camera:- Image Sensor: OV 7949 1/3in color CMOS
- TV System: PAL / NTSC
- Total Pixels: PAL: 628 x 586 NTSC: 510 x 496
- Resolution: 420 TV lines
- Minimum Illumination: 0.1Lux(iRON)
- Video Output: 1.0Vp-p into 75Ohm
- Power Supply: DC12V ≤ 130mA(IR ON)
- Operating Temperature: -20C° ~ +70°C
Monitor:
- Type: Digital TFT LCD
- Display Size: 3.5inch
- Display Format: 4:3
- Power: ≤3W
- Power Supply: DC12V
- Video: 1 rearview video input / 2AV input cauto switch when reversing
- System: PAL/NTSC auto switch
- Contrast: 350:1
- Pixel: 480 x 234
- Installation: Install on the dashboard with
- Operating Voltage: DC9V-16V
- Environment Humidity: 10%-90%
- Operating Temperature: -20℃ ~ +60℃
- Storage Temperature: -40℃ ~ +85℃
Details:

- Well packed 3.5in LCD car rear view monitor set with 1/3in COMS Camera

- The car rear view monitor set features easy installation and is simple to use

- This design of car rear view camera is stylish and delicate

- The rear view car camera features Hi-Q High quality compact material

- The car rear view monitor set features full-scaled enhanced signal reception

- The car rear view monitor set is especially useful in tight parking lots
Operation:
- Connect the yellow video jack vith monitor video input jack
- Conenct the red (or black) power input jack with power supply
Precaution:
- Recommend using regulated DC12V power supply unit with camera for best picture and for safe operation of the unit
- Do not cut power input jack and connect the conductor to power supply directly, bacause that will fatally injured the camera
- Do not attempt to disassemble the camera. There are no user serviveable parts inside. Refer servivcing to qualified service person
How to Install a Rearview Mirror Monitor in Your Car:
- Disconnect the battery cables from the battery before beginning installation. Use a wrench or socket to remove the battery cables. Check the vehicle's repair guide for the proper wrench or socket size.
- Remove the original rearview mirror from your car. Leave its mounting bracket on the windshield-you'll attach the rearview mirror monitor to this. Check the rearview mirror's mounting screw to see what size screwdriver you'll need
- Insert the rearview mirror monitor into the existing mounting bracket on your windshield. Use the bolt supplied with the monitor to secure the device in the mounting bracket
- Route an A/V power cable from the A/V selector box to the monitor. Connect the A/V cable from the monitor to the A/V power cable. Use cable ties to secure the cables and prevent them from hanging
- Reconnect the battery. Start your vehicle and select the rearview mirror monitor on the A/V selector box. The video monitor should come on if the rearview mirror monitor is correctly installed
How to Install a Rear-View Camera in Your Car:

Rear-view cameras are especially useful in tight parking lots, dark areas or in places where children might be running around. You can install as many of these cameras as you want, though one or two is usually enough- Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts
- Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal
- Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out
- Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight
- Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse
- Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions
- Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you
Tips & Warnings:

- Don't rely solely on the rear-view camera when backing up. Use it as a supplementary aid
- You must have the rear-view monitor set up and installed correctly to receive the video signal from the rear-view camera
- Don't install the camera (or any electrical device) with the battery connected, or you'll risk a severe electric shock
Package Included:
- 1 x Monitor
- 1 x Bracket
- 1 x Camera
- 2 x Connecting Cable
- 1 x Pad
Get DinoPoint™ by Writing reviews, Post Images, or Post Videos. The first five customers can get double points!
David Bank
from ()
Bought this item on
08-23-2011- Other Thoughts: Overall, it has a clear view, (needs to be cleaned when it rains) and it serves the purpose.
Was this review helpful?
Brad Spillman
from ()
Bought this item on
08-02-2011- Other Thoughts: Fast delivery, good price and back in the air. Super service!
Was this review helpful?
Jeff Stroud
from ()
Bought this item on
05-24-2011- Other Thoughts: It is a very usefull Car Rear View Monitor Set, easy to install and works in any condition that is required, the only problem is that you loose the perspective and you can't see the distance
Was this review helpful?
Elizabeth M Smith
from ()
Bought this item on
06-22-2011- Other Thoughts: Great product and it arrived very quickly. No complaints. Straight forward product and straight forward transaction. Thank you! Would buy from this seller again.
Was this review helpful?
Aaron Stewart
from ()
Bought this item on
07-05-2011- Other Thoughts: The product purchased was exactly what i paid for and I am excited to be able to get what I did so fast!
Was this review helpful?
Maybe you are interested in:






















































