-
-
Specifications:
Monitor:
- Inset super powerful reception
- All supplement channels receipt, with 160 preset channels
- Chinese-English menu changeable and blue background display
- TV Calendar displays year, month and date
- Timed auto turn on and off
- All-function remote controller
- Multi-system choice for the customer, such as PAL, NTSC
- AV input
- Can be powered by AC or DC 12V automobile storage battery
- Automatically turning system
- Screen Dimensions: 3.5 inches
- Display Component: Color TFT-LCD
- Pixel: 480 x 324
- Aspect Ratio: 4:3
- Contrast Ratio: 350:1
- Response Time: B→W 30ms W→B 10ms
- Video Frequency: PAL/NTSC
- Video: 2AV input cauto switch when reversing(Auto power on when detect AV signal)
- Power Supply: DC12V
- Power Consumption: Around 3W
Camera:
- Image Device: 1/4 inch color CMOS OV7950
- TV Stystem: NTSC
- Effective Pixesls: 628 x 582 pixels
- Sensing Area: 5.78 x 4.19mm / 4.69 x 3.54mm
- Sync. System: Internal
- Resolution: 420TV lines
- Minimum Illumination: 0.5Lux / F1.2
- Lens: 2.1mm
- Lens Angle: 170deg
- S/N Ratio: More than 48db
- Electronic Shutter: 1/60-1/15,000 seconds
- Video Output: RCA connector, 1.0vp-p, 75ohm
- Current Consumption: 90mA
- Power Supply: 12V DC
- Operating Temperature: -10 to 50degrees ccentigrade, RH95%
- Storage Temperature: -30 to 60degrees centigrade, RH95%
- Other Items: Automatic white balance, AGC and BLC
- Size: 16 x 35 mm / 0.63 x 1.37 in
Details:

- The monitor detects when you back up and shows the camera on screen

- This desige of Car Reariew is very easy to install

- Simple and easy to install

- Rear-view camera is especially useful in tight parking lots
Precautions:
- Recommend using a regulated DC12V power supply unit with camera for the best picture and for safe operation of the unit
- Do not cut the power input jack and connect the conductor to power supply directly, because that will fatally injured the camera. If you have to connect the conductor, please use our cable in accessories
- Do not attempt to disassemble the camera. There are no user serviceable part s inside. Refer servicing to qualified service person
How to Install a Rearview Mirror Monitor in Your Car:
- Disconnect the battery cables from the battery before beginning installation. Use a wrench or socket to remove the battery cables. Check the vehicle's repair guide for the proper wrench or socket size.
- Remove the original rearview mirror from your car. Leave its mounting bracket on the windshield-you'll attach the rearview mirror monitor to this. Check the rearview mirror's mounting screw to see what size screwdriver you'll need.
- Insert the rearview mirror monitor into the existing mounting bracket on your windshield. Use the bolt supplied with the monitor to secure the device in the mounting bracket.
- Route an A/V power cable from the A/V selector box to the monitor. Connect the A/V cable from the monitor to the A/V power cable. Use cable ties to secure the cables and prevent them from hanging.
- Reconnect the battery. Start your vehicle and select the rearview mirror monitor on the A/V selector box. The video monitor should come on if the rearview mirror monitor is correctly installed.
How to Install a Rear-View Camera in Your Car:
- Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts.
- Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal.
- Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out.
- Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight.
- Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse.
- Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions.
- Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you.
Package Included:
- 1 x Monitor
- 1 x Camera
- 1 x Video Cable
- 2 x Connect Cables
Get DinoPoint™ by Writing reviews, Post Images, or Post Videos. The first five customers can get double points!
S. Farshchi
from ()
Bought this item on
05-18-2009- Other Thoughts: Bought it to monitor a patient room's from a next floor up. Very easy to set up and get going. The picture is very good and the product functions exactly as advertised.
Was this review helpful?
Maybe you are interested in:






















































