Specifications:

• SNMP Version: SNMP version 1, 2c
• Diagnostics: Flash, RAM, LAN, WLAN
• Spec. /Modulation: Radio and modulation type: 802.11b/DSSS, 802.11g/OFDM
• Data Rates: Data rates supported: 802.11b: 1, 2, 5.5, 11 Mbps; 802.11g: 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps
• Channels: Operating channels: 11 North America, 13 most of Europe (ETSI and Japan)
• External Antennas: 2 (Omni directional)
• Antenna Connector Type: Fixed
• Transmit Power: Transmit power (adjustable) at normal temperature range: 802.11.g: typical -18 dBm, 802.11.b: typical -20 dBm
• Adjustable Power: Yes
• Antenna Gain: 2 dBi
• Receiver Sensitivity: 802.11.g: 54 Mbps at -69 dBm; 802.11.b: 11Mbps at - 86 dBm
• Wireless QoS: WMM, 802.11e ready
• Wired Equivalent Privacy (WEP)/WPA/WPA2: WEP 64 bit/128 bit, WPA Temporal Key Integrity Protocol (WPA-TKIP)/Advanced Encryption Standard (AES), WPA Pre-Shared Key (WPA2-PSK), WPA2-ENT
• 802.1X RADIUS Authentication: 802.1 xs: RADIUS (Message Digest Algorithm 5 [MD5], Secure Hash Algorithm 1 [SHA1], Transport Layer Security [TLS], Tunneled TLS [TTLS], and Protected Extensible Authentication Protocol [PEAP]), dynamically varying encryption keys
• Access Control: Access control list (ACL) capability: MAC and IP-based
• Firewall: Tasteful packet inspection (SPI) firewall
• DoS: DoS prevention
• VLAN Support: 4 LAN ports and 4 SSIDs can be mapped to up to 5 VLANs
• SSID Broadcast: SSID broadcast enable/disable
• Multiple SSID: Supports up to 4 SSIDs
• Wireless VLAN Map: Supports SSID to VLAN mapping with wireless client isolation
• Wireless Domain Services (WDS): Allow wireless signals to be repeated by a repeater
• DMZ: Software configurable on any LAN port
• VPN: 10 IPsec tunnels, 3DES/AES encryption, MD5, SHA1 authentication, IPsec NAT transparency (NAT-T), Quick VPN support
• Routing: Static and Routing Information Protocol (RIP) v1, v2
• Dimensions: 7.32 x 6.89 x 1.89 in/170 x 42 x 193.5 mm (W x H x D)
• Power: 12V 1A DC input
• Certifications: FCC, IC-03, CE
• Operating Temperature: 32º to 104ºF (0º to 40ºC)
• Storage Temperature: -4º to 158ºF (-20º to 70ºC)
• Operating Humidity: 10% to 85% no condensing
• Storage Humidity: 5% to 90% no condensing
• Ports: Ethernet, Antenna, Power
• Frequency Band/Bandwidth: 2.4 GHz IEEE 802.11b/g ISM Band
• Standards: IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, 802.1x (security authentication), 802.11i ready (security WPA2), 802.11e ready (wireless QoS)
• Operating System: Linux

Details:

• The 2.4GHz Wireless Router support Flash, RAM, LAN, WLAN diagnostics

• Enjoy a better and faster surfing speed with this compact LAN Wireless Router

• Made of high quality material, the LAN Wireless Router is durable and reliable for long time use

Introduction:











How to Connect a Wireless N Home Router to a PC:

As wireless technology has advanced, different signal standards have been created to signify more powerful wireless signals with faster transfer rates and a longer range of connectivity. The first of these standards was wireless B, followed by wireless G. Though G was compatible with wireless receivers and devices designed for B, they were not able to make full use of the expanded signal strength that G offered. With the advent of wireless N, the same compatibility occurred; a wireless N signal is capable of working with B and G devices, but these devices won't receive the full benefit of wireless N's improved signal strength. When setting up a wireless network with a wireless N router, the first thing that you need to do is make sure that you are using components designed to make full use of the wireless N signal.

• Power down the PC that you plan on connecting to the Internet via your wireless N router. Remove the side panel so that you have access to the inside of the PC, then choose an expansion slot to install your wireless N receiver card into. Remove the small screw from the expansion slot cover using your Phillips screwdriver, setting the cover and the screw aside; plug the receiver card in to the slot securely and then use the screw to finish mounting it in place. Don't forget to attach the receiver card's antenna after the card has been installed.
• Replace the side panel on your computer and reboot. Your operating system should recognize the new hardware that you have installed and will ask to install the drivers for the receiver card. Use the driver disc that came with the wireless card to install the drivers, then reboot your computer once again.
• Connect your wireless N router to your modem via the Ethernet cable supplied with your modem. Plug in the power cord of the router and wait a moment as it goes through its startup routine (you should see several lights on the router flash, though the exact startup routine will depend on the manufacturer). As soon as the lights stabilize, the router will be broadcasting a signal.
• Run your operating system's network connection wizard. The wizard will give you the option to connect to a wireless network; simply follow the on-screen prompts. If the wizard doesn't give you a wireless option, finish the wizard in order to set up your network preferences and then right-click on the wireless icon in your system tray. Select "Connect to a Wireless Network" (the exact text may differ) from the menu that opens.
• Log in to the router using the IP address provided with the router's setup guide in order to set the router's wireless Internet options. This will give you an opportunity to create an encrypted security key (which you will need to input on your computer by going through the "Connect to a Wireless Network" step again; you will be prompted for the security key this time before you will be allowed to connect). You can also set a password for the router's administrator account to further improve network security.
• Repeat the installation and network connection processes on any other computer that you wish to connect to your wireless N router. Remember that you will have to input your security key on each computer, so make sure that you have it written down.

Package Included:

• 1 x Wireless Router