2 x 48 LED Car Flash Red and Blue Strobe Light HS-51025A

Specifications:

• Light A flash quickly for 8 times. Light B flash quickly for 8 times. Repeat continously
• Light A flashes once. Light B flashes once. Repeat continously
• Light A and B flash once at the same time. Repeat continously
• Voltage: 10.5V~13.5V
• Dimensions: 185 x 65 x 28mm / 7.28 x 2.56 x 1.1in(L x W x H)
• Light Color: Red and Blue
• Output Power: 4W~6W

Details:

• With all the new technology coming out for the new vehicles on the market, LED lighting is one of the most exciting innovations

• The bright lights can be seen from a greater distance.The car turning light is angled allowing you to position it most effectively for your car whilst the heat-resistant construction ensures that the colour won't fade or the casing become misshapen. It will reflect the lights from other car to remind other drivers to notice your car

• Greater safety for your vehicle.It has flexible lights which have 48 super-bright, amber LED bulbs in each. Say goodbye to bumps from the turning and make sure the car definitely knows when you're about to turn with an extra car turning light

• The Car Turning Light is a smart, dash-mouted warning light which utilizes total internal reflector technology. The Car Turning Light is easy to install and with adjustable angle, the Car Turning Light can be seen from a greater distance offering increased visibility and therefore greater safety for your vehicle

• Automotive LED Car Light Bulbs gives you all the benefits of LED lighting, which you cant get from Car Light. Plus, this super ultra bright LED Car Light Bulbs features a super bright red and blue color

Size in Detail:

How to Connect Motor Vehicle LED Lights:

• Locate areas under the motor vehicle body or fairing where you would like to install the LED lights. Ensure that there are no hot motor vehicle parts close to the locations you pick
• Clean the areas where you will be installing the lights with alcohol prep pads. This removes the dirt and grime. Allow the alcohol to dry thoroughly so the LEDs will have a clean, dry surface to attach to
• Remove the adhesive backings on the LEDs and install them by pressing them firmly against the motor vehicle surface. Most LED light strips are flexible and can be curved around the fairing for better illumination
• Remove the seat and run the wires through the frame of the body to underneath the seat where the battery is located. The wires should not be visible on the outside of the bike
• Collect all the wires and tighten them together with a wire tie. This keeps the wires organized
• Loosen the terminal bolts on the motor vehicle battery by using your screwdriver. Tighten the terminal bolts back into place so they firmly hold the wires down
• Start your motor vehicle and watch your LEDs light up. If all or some of the LEDs are not operating properly, check the battery terminal connections first to ensure that they are tight. If the problem is not resolved, check the clamp connector wiring to ensure that all the wires are stripped properly and in full contact with the inside of the connector

How to Install LED Lights on a Car:



LED lights are a popular aftermarket option for most vehicles as they are brighter-than-normal halogen bulbs and last a lot longer while using less power. The problem with installing LED lights on your vehicle is that you cannot simply swap out the bulbs. You actually need to replace the entire light assembly. The two most common lights that are converted to LED are the headlights and taillights. In order to do so, you must remove the old headlight/taillight assembly and install the new LED assemblies

Headlights:

• Turn the vehicle's engine off and open the hood
• Disconnect the electrical connection harness from the rear of the headlight assembly. Some vehicles require you to remove a rubber seal or cover to access the connector
• Remove the fasteners securing the assembly to the engine compartment. Most vehicles have screws that can be removed with a Phillips screwdriver, but others have bolts that need to be removed with a socket wrench. Pull the assembly out of the engine compartment
• Install the LED headlight assembly and reinstall the fasteners. Reattach the connector harness and the rubber seal/cover if necessary
• Repeat with the other headlight assembly and close the hood

Taillights:

• Turn the vehicle's engine off and open the trunk
• Remove the two screws or bolts securing the taillight cover to the trunk and remove the cover
• Disconnect the taillight's electrical connector harness and remove it from the vehicle
• Install the replacement LED assembly and reconnect the harness. Reinstall the cover and screws
• Repeat with the other taillight assembly and close the hood

How to Replace Car Lights:

• Changing your car lights, specifically its headlights, is a task that most people would prefer to have a specialist do. While it is true that having a mechanic replace your headlights can cost you a lot of money, some people would rather spend a few dollars than to tire themselves out while doing the task themselves. In truth, replacing car lights does not have to be a stressful activity. With the right tools and materials, you can replace your own car headlights. Here is how you can accomplish the task yourself
• Pop your car hood and examine the headlight assembly. Check behind your headlight and see if you need additional tools to access it. While most cars allow easy access to their headlight bulb without any tools, some may require a screwdriver, pliers or wrench to remove its plastic cover
• Turn the car engine off and remove the covers and parts that are blocking the rear side of your headlight assembly
• Hold the headlight module from the headlight assembly's rear, and twist it counter-clockwise to fully release it from the assembly. Pull the headlight module straight out after twisting
• Pull the headlight module bulb in order to disconnect it. Install your new bulb in its place. Some bulbs may require a twist and pull, depending upon the model
• Place your headlight module back into the headlight assembly's rear, twisting it in clockwise direction until it comes to a full lock
• Put back the removed panels on the back of the headlight

Warnings:

• Ensure that your replacement bulb is compatible with the vehicle model. When visiting your local store for auto parts, ask the representative for the bulbs that are compatible with the car

Package Included:

• 1 x Flashing Car Grille Strobe Light
• 1 x LED Controller Box 
• 1 x Pack of Screws