ZiGuang JetTech 6092 Mini High Precision Wired 3D USB Retractable Scroll Wheel Optical Mouse

Specifications:

• Excellent 3D optical mouse for mobile professionals
• Mini mouse with 2 standard buttons plus a scroll wheel for fast navigation while working
• Plug and play, no driver needed
• Scroll wheel mouse is comfortable for both left and right hands use
• Clip design is great to hang on a purse, bag, backpack, key ring or wherever you want
• Retractable cable of the USB mouse can be extended up to 68cm
• Color: Orange
• Dimension: 7.5 x 4 x 2.1cm/3.0 x 1.6 x 0.8in(L x W x H)
• Work with: Windows 2000, Me, XP and Vista

Details:

• JetTech 6092 Mini High Precision Wired 3D USB Optical Mouse that is excellent 3D optical mouse for mobile professionals

• Mini and nice mouse with 2 standard buttons plus a scroll wheel for fast navigation while working

• The smile face of the USB mouse. Scroll wheel mouse is comfortable for both left and right hands use

• Clip design of the USB mouse is great to hang on a purse, bag, backpack, key ring or wherever you want

• Take the retractable scroll wheel mouse on the road easily, and use the USB mouse with optical precision on most surface

How to Clean an Optical Mouse:

• The optical mouse is gradually replacing the trackball mouse on most computers. While it requires less maintenance it still can eventually build up dust and dirt making the mouse jerky or unresponsive. Here's how you can clean an optical mouse.

Instructions:

• Turn off your computer and unplug the mouse
• Look at the lens on the bottom of the optical mouse. If you see any debris see if you can blow it off. If not take a Q-tip and rubbing alcohol and lightly clean the lens
• Next look at the small rubber pads on the bottom of the mouse. Dust and dirt tends to build up here making the optical mouse not move smoothly. Scrape as much of the gunk off as you can with your fingernail
• If there is something sticky on one or more of the pads use Goo-Gone to dissolve it. Always make sure you don't use too much of any liquid when you clean an optical mouse. It is a piece of electronics, and you want to avoid getting liquids in to the interior
• Take a damp cloth and wipe any remaining dirt and dust of the pads of the optical mouse
• Plug the mouse back into the computer, and enjoy your newly cleaned optical mouse

How to Fix an Optical Scroll Mouse:

• Sporadic/erratic behavior, often caused by one of two things. Cat hair and synthetic carpet fiber. Both lightweight, they can easily disperse or interrupt the LED's light path and confuse the sensor
• Locate the place where these fibers most often get caught up. The underside of the Mouse at the optical window. You can try to blow the fibers out or pick them out with a pair of tweezers. You cannot stop fibers from getting caught here. If you were to apply transparent tape over this window, it would blur the LED's view and reduce its functionality. Besides, the static electricity and adhesive would attract and hold more fibers
• Locate the biggest culprit. The scroll wheel! There is a wide enough opening around the wheel to allow plenty of fibers to get pulled through as the wheel is turned. Once that fiber reaches the internal eye, it gets caught between the LED and the refracting lens. This splits the single beam of light into multiple beams which confuse the sensor and sends the cursor into a wild dance
• Turn off your computer and unplug the Mouse. Flip the Mouse over and, using a small Jeweler's-type Phillips head screw driver, remove the screw holding the two halves together. Gently separate the two halves, careful not to break off the alignment tabs or knock the wheel off of its axis
• Inside, you will see the LED mounted on the circuit board pointing towards the triangular refracting lens (circled in red)
• Using a piece of electrical tape works great for removing the fibers from around and between the LED and Lens. Take care not to get any adhesive on either of these places. You can use compressed air or a pair of tweezers too. While you're in there, you may as well remove all the fibers from the rest of the board and wheel assembly
• Cut three pieces of electrical tape and apply them as shown, with one long piece front to back and two shorter pieces side to side. This effectively shields the LED and blocks any fibers from causing future interference. The LED and chip do not produce enough heat to require ventilation. So, covering them is fine. Once you have shielded the LED, reassemble the Mouse

Package Included:

• 1 x JetTech 6092 Retractable USB 3D Optical Mouse