-
-
Specifications:
- Can be a one to one control (a remote control of a vibrator); also be one to many controls, (ie, more than a remote control vibrator); such a remote control holder and the holder of the vibrator can be adopted by way signal transmission between remote control, high reliability, informative, hidden strong. to communicate without openings can also be, exchange, tips, hints, warning effect
- Hold down the learn button and hold light flashes, press the release button learning remote control eliminate any key indicator that a successful study
- The wireless vibration reminder can learn a fixed code remote control, learning remote control codes. Only allows a machine to learn a remote control
- Adopt advaned technology, the wireless vibration reminder is great in perforamance
Wireless Vibration Reminder:
- Operating Frequency: 315MHZ/433MHZ
- Operating Voltage: DC1.5V (7 batteries 1)
- Current: 100mAh (vibration)
- Quiescent Current: 8.2mAh
- Vibration Frequency: 50 ~ 75HZ / sec
- Dimensions: 58 x 35 x 16mm / 2.28 x 1.38 x 0.63in
- The wireless vibration reminder design of advanced, reliable, and B is mainly used for two (or more) in inconvenient places speech, mutual remote control to remind each other, and make the appropriate action or behavior
- Because it is wireless remote control vibrating mode are not afraid of obstacles blocked, ensuring the effectiveness of information transmission and hidden, and is indispensable for special occasions communication tool
Remote Control:
- Operating Voltage: DC12V (23A/12V battery 1)
- Operating Current: 10mA
- Radiated Power: 10mw
- Modulation: ASK (AM)
- Transmission Frequency: 315, 430, 433 MHz (SAW frequency stabilization can be customized according to customer's special frequency points)
- Transmission Distance: 200M (Bare zone, the receiver sensitivity is negative 100dbm)
- Encoder Type: Fixed Code
- Uses: Motorcycle, automobile anti-theft products, home security products, short-range wireless remote control products, industrial control products
- Features: Sleek, upscale look and feel
- Dimensions: 58 × 39 × 14mm / 2.28 x 1.54 x 0.55in
- The wireless remote control feature 4 keys design, easy and convenient to use
- With keychain design, easy and convenient to take the wireless remote control with you
How to Reset a Remote Control:
If you want to add another remote control for your garage door opener or need to replace a dead battery and reprogram an existing remote, chances are you'll have to reset the opener with the base unit for it to work. The process involves just a few steps and is relatively easy to do- Replace the battery by opening the remote, taking out the old one(s) and putting in the new one(s). Make sure you buy the right battery for your remote. Match the battery type, size and voltage that came with the remote
- Use a step ladder to access the garage door motorized unit, usually equipped with a safety light. Locate the reset or "learn" button on the unit. Many times, this small button is recessed, so you might need a pen or pencil to reach it
- Push the reset or "learn" button on the opener. While the reset indicator light is blinking for about 30 seconds, point your remote at the opener, then press and hold the remote button that opens the door, and the reset light should stop blinking and glow steady to indicate the controller and opener are now synchronized. If the process doesn't work the first time, try again to make sure you pressed your button during the time when the indicator light is blinking
How to Build a Wireless Remote Control:
Simple wireless devices use various components to activate an infra-red signal that broadcasts to a receiver box, allowing the user to program the control. Basic wireless remote controls simply turn a device on or off. Components used in a wireless device can be found at most electronics outlets and hobby shops. Specialized retail establishments have pre-packaged kits that can be used by a beginner. At the very least, even experienced electronics enthusiasts use pre-made remote control boxes due to the simplicity of their design, including ergonomic support. The structure of the wireless remote control provides a builder with not only knowledge but the reasons a receiver can be controlled by the device
- Open the remote control housing and place a push button switch on the side. In the upper right corner of the housing, fasten a 3-volt battery holder. Be sure enough room is available to install and remove the battery
- Run a wire from the push button switch and link to the 3-volt battery holder at the negative connection. Attach another wire to the push button switch and lead it to the Meg 1/4W resistor and the NPN silicon transistor. Run a third wire from the Meg 1/4W resistor and attach it to the 22K 1/4W resistor and and the PNP silicon transistor
- Position the infra-red LED on the front of the housing. Attach the LED and run wires to both transistors. From the 22K 1/4W resistor, run a wire to the C220.01uF 16v ceramic disk capacitor. Run another wire between the NPN silicon transistor and the ceramic disk capacitor
- From the positive connector on the 3-volt battery holder, connect a wire to the PNP silicon transistor. This will allow for proper current flow in a closed circuit. Ensure the push button switch is positioned to "off" and place a 3-volt battery into the holder. Close the remote control housing
- Point the remote control at a receiver, making sure the LED on the control is aimed at the LED of the receiver. Push the button and the receiver should power on and off. To adjust the receiver to be programmed, point the remote control and hold down the push button switch. Adjust the pot or taper on the receiver
Package Included:
- 1 x Wireless Vibration Reminder
- 1 x Remote Control
Get DinoPoint™ by Writing reviews, Post Images, or Post Videos. The first five customers can get double points!
Belle
from ()
Bought this item on
10-20-2011- Other Thoughts: Bought this Wireless Vibration Reminder for my mom, who has a very severe hearing loss. It is relatively flat, so it doesn't bulge out from under her pillow. It vibrates very strongly! No more missing the wake-up call for her!
Was this review helpful?
Audrey
from ()
Bought this item on
08-18-2011- Other Thoughts: that said, I would still make the purchase again. It performs as advertised and I wouldn't want to be without it. Vibration Reminder is the best travel alarm I've used.
Was this review helpful?
Zachary
from ()
Bought this item on
07-13-2011- Other Thoughts: for this alarm, I figured that this Vibration Reminder would be the best thing for my 14 year old son. He has such a hard time waking up in the morning. We even tried holding one of those alarms that have the two bells on top that clank over his head and that did not wake him up.
Was this review helpful?
Milo
from ()
Bought this item on
03-18-2012- Other Thoughts: The Best part of this clock is the vibrating sensor that goes under his head and can be set to gently vibrate to wake him instead of me having to shake him out of bed... Great purchase... Enjoy!
Was this review helpful?
Eudora
from ()
Bought this item on
01-13-2012- Other Thoughts: The alarm noise & vibration goes on for a full minute if left untouched, then seems to automaticly reset for the next day. <br/>I don't think I'll ever need a different alarm, I might purchase another just in case I ever damage or lose this one! LOVE IT!!!
Was this review helpful?
Maybe you are interested in:
