Customers Also Bought
- Brand new and high quality 2.4GHz Wireless Receiver
- Compact design 2.4GHz Wireless Receiver is easy to set up
- Manual or remote controlled
- Four channels available, AV out
- Channel scan and channel skip for multiple cameras
- This 2.4GHz Wireless Receiver System allows you to transmit video and audio to one location to another
- It's so powerful that you can receive signal more clear and stable
- Easy operation & installation, Wireless Security System is designed for transmitting video and audio signal to a second television within the house. For example a VCR or DVD could be transmitted from your main viewing area to a bedroom or games room
- Receiving Frequency: ISM 2400~2483Mhz
- Intermediate Frequency: 480 MHz
- Frequency Stabilization: +/-100 KHz
- Demodulation Mode: FM
- Antenna: 50ohm SMA
- Receiving Sensitivity: <-85dBm
- Video Output: 1Vp-p@75, S/N>38dB
- Audio Output: 1Vp-P@600
- Power Adapter: DC 12V/500mA
- This Wireless Security System is compact design and easy to set up
- 2.4GHz wireless A/V kit, This 2.4GHz Wireless Security System allows you to transmit video and audio from one location to another which is perfect for home and office using
- This Wireless Receiver System is well-designed with four frequencies and very easy to install and use
- New 1.2GHz wireless AV transmitter receiver
- Wide transmitting range (depending on environments)
- Microwave of anti-interference
- Excellent Audio & Video collection
- AV (Audio/Video) Wireless Transmitter
- Q3, VC1, C13, C16 and L3 all make up a colpitts oscillator circuit that fluctuates form 220~250MHz. You can regulate the frequency to any value within this threshold by tuning VC1 or L3. C13 modulates the signal rate. When the capacitance increases, so does the modulation. R9 and C16 bias the local oscillation. If you lower R9's frequency to 680W the oscillator's output level will increase.
- Q2 and L2 act as a frequency doubler. C7, along with FCZ7S3R5 (IF transformer), the Q4 transistor, C14, C19 and R12 all make up the mixer. This mixer takes both audio and visual signals together and "mix" them into one and passes through RF Amplifier Q1 to transmit the signal to the antenna.
- Fix the Transmitter, using the RCA Video, the Audio signal cable connect the transmitter and the single original equipment (eg, Camera, VCD)
- Check the two machine on the suitable position, then inserting the power adapter
- The Transmitter's installation is nearly the same as the receiver's, just the receiver need to be connected with the display equipment
- Confirm that it's right to install the Transmitter and the Receiver in two places, you can open all the power switches and set the Transmitter and the Receiver as the same channel
- Observe the accepting effect, by adjusting the tact of the angle of the Transmitter and the Receiver' antenna until get the excellent Video and Audio effect, the installation is over
- You'd better install it at the place where children cannot touch
- Please pull the transformer out when you stop using it
- Do not touch the emission antenna in case you will be burned when the transmitter is electrified
- Do not expose it at the damp place for preventing it from water or protecting people from electric shock
- Please use the transformer produced by our company. Or our company will not be in charge of any damage incurred by the product
- Our company will not be responsible for any damage incurred by your amending or dismounting without a permit
- Meets the power source adapter to the launcher, meets the power source, the red candle brightly, proved the launcher circular telegram is successful
- Another power source adapter meets to the receiver input end, meets the power source, the red candle brightly, proved the receiver circular telegram is successful
- Uses the sound video frequency line the launcher and the supply oscillator (for example DVD, camera) docks, the receiver and the monitor docking, the launcher, the receiver frequency channel selection switch dials to the identical position, the monitor demonstrated the supply oscillator spreads the picture, the installation completes
- 1 x 2.4GHz Wireless Receiver
- 1 x Remote Controller
If the order has not been shipped; please contact DinoDirect Live Support for order cancellation.You will get your refund within 24 hours.
If the order has already been shipped; you may return the item to us postmarked within 30 calendar days of delivery. Before that, please contact our Live Support to inform that.
In that case we will refund you the payment excluding actual shipping fees already incurred.
If the item is defective, please contact DinoDirect Live Support and send an email to us at email@example.com attached an image or video file clearly showing the defect of the product. And we will give you a response within 24 hours whether we will resend the item or refund the payment to you for compensation.
For customization, please consider carefully before ordering.Because we do not accept return and replacement.
|Unit Price||USD$ 31.76||USD$ 30.60||USD$ 29.44||USD$ 27.90|
|Enter Wholesale Channel>>|
• If the order has not been shipped; please contact DinoDirect Live Support for order cancellation.You will get your refund within 24 hours.
• If the order has already been shipped; you may return the item to us postmarked within 30 calendar days of delivery. Please contact our Live Support to inform that.
• Please contact Live Chat or click here to learn more return policy.