Deli 7623 Office Desktop Business Card Holder

Specifications:

• Made of high quality material
• You can gather your Card
• Modelling is contracted, large amount of storage 
• It is a good decoration to embellish your desk
• A sleek and compact storage solution that keeps your cards clean, undamaged
• It is a perfect gift for someone special or treats for you
• Can be used in hotel, counter, exhibition, front desk deposit card, providing the customer for himself
• Size: 103.5 x 45.5 x 50.5mm/4.07 x 1.79 x 1.99in(L x W x H)

Details:

• This Business Card Holderp is very welcomed by most people because of its simple design

• The Desktop Business Card Holder is made of high quality material, with smooth surface, durable and comfortable for your daily use

• This Business Card Holder makes your desk looked clean and tidy, also is a great addition to your desk

Size in Detail:

• 1

How to Make a Business Card Holder:

In today's world, business cards are a must for the professional, the self promoter, and the convenience of swapping an address. There are many different types of business card holders on the market, but with a few minutes of your time and a little creativity - you can make a business card holder that is uniquely your own.

• Instructions
• Choose a trendy or plain designed fabric of your liking. Dig through some scrap material left over from other projects, or if you are going to your local fabric outlet pick up a fat quarter.
• Some fabric outlets have various size pieces already cut or left over from the bolt they roll up and sell at discount prices.
• Create your pattern. You will need a piece of paper, ruler, and a pencil.
• Measure a rectangle 4 inches wide by 9 inches long and cut out.
• Fold your paper rectangle in three equal parts.
• At one end of a third take a can good and curve both edges and trim curved edge with paper
• Pin pattern to fabric and cut. You will need two pieces of fabric and one piece of fusible interfacing.
• Fuse interfacing to wrong side of one piece of fabric. Make sure you place the interfacing shiny side down on the fabric.
• Right sides together stitch around fabric leaving a 1 - 2 inch opening at the bottom.
• Turn right side out, stitch closed opening, and press with hot iron.
• Fold fabric in thirds. Pin bottom section in place to hold and stitch down both sides.
• Using a sew on snap place one side of snap in middle of bottom portion of business card holder and stitch in place.
• Stitch the other half of snap onto the inside of top flap in position to connect with the bottom portion of snap.
• (You can substitute Velcro for the snap if you want.)
• Next time someone wants your business card you'll not only have them available, but in your very own stylish card holder.

How to Sculpt a Business Card Holder:

Whether you sculpt in wood, wire, stone or clay, the basic premise of a business card sculpture is the same. You need to create within the sculpture, a background prop on which the business cards may lean in an upright position, and you need a foreground structure to stop the bottom of the business cards from falling off. With that basic structure, you can sculpt a myriad of creations to hold business cards.

• Instructions
• Choose the material with which you would like to sculpt and gather any relevant tools (pliers, gouges, saws, metal snips).
• Wood, wire and clay are common sculpting choices, and the materials and tools are readily available in most households and hobby stores.
• Choose an image and determine background and foreground.
• Sketch out the desired image.
• The majority of the image should appear above the area where the business cards will sit. For business card sculptures that focus primarily on the background image, you may consider a face or bust, a treble clef, a dolphin, or any image that can be sculpted in silhouette, relief or three dimensionally.
• Sculpt the base or connect the background and foreground while making sure the card slot is an appropriate size and angle.
• For full figure sculptures, the body usually joins the background and foreground. For single image examples, use sculpting materials to form the slot in which the business cards will sit. The slot is generally formed with right angles.
• This structure should complement the background and provide a stopping mechanism for the card slot. You may want to consider how much of the foreground may cover or display the business cards.
• Add final touch ups and test the sculpture with business cards.

Package Included:

• 1 x Office Desktop Business Card Holder