EMORA Premium Acrylic LCD Panel Protector for Canon 5D

Specifications:

• This clear transparent screen LCD panel protector offers ultimate protection against scratches and dirt
• LCD panel protector helps protects your camera screen against daily usage and scratches
• LCD panel protector offers a high visible light transmission, which has minimal effect on the brightness of your digital camera
• Acrylic protector can reduce the strain of your eyes by filtering to the UV light emitted form your camera display
• Protector for Canon is easily installed and is bubble free when installed properly
• Compatible with: Canon 5D
• Material: Acrylic

Details:

• LCD panel protector offers a high visible light transmission, which has minimal effect on the brightness of your digital camera

• You can image the size of the protector for Canon according to the coin. Then take this home now

• Scratch proof your camera screen with the invisible, durable and useful camera screen protector

• This clear transparent screen LCD panel protector offers ultimate protection against scratches and dirt

How to Install a Screen Protector:

• Protecting a liquid crystal display on electronic equipment or a laptop is important ensure permanent damage does not occur to a delicate LCD. Installing protective film can be tricky because if the screen is not completely clean, dirt will be trapped beneath the screen protector. Additionally, if care is not taken to adhere the protector, it might not go on smoothly and without wrinkles

Instructions for Attaching a Screen Protector:

• Because many electronics devices have liquid crystal display screens, screen protectors have grown in popularity. To keep an LCD screen clean and avoid scratching the fragile surface, you should cover it with a clear screen protector. The screen protector adheres directly to the LCD screen and covers it entirely. With the screen protector in place, you can then relax and stop worrying about permanent scratches in the LCD screens of your electronic devices

Important:

• Please note that one side of the LCD panel protector had anti-scratch coating as indicated by the label, The other side has been silkscreen according to the LCD panel and therefore does not have anti-scratch coating

Installation:

• Remove the protective liner from the silkscreen side
• Gently clean the exposed panel protector side with the protector liner removed with a clean microfibre cloth. Be careful not to apply too much strength as residue on the microfibre cloth may cause any scratches as this side does not have anti-scratch coating.
• Measure cut and paste the supplied adhesive according to the black silkscreen area.
• Clean the camera LCD panel to remove dust or tiny residue
• Use a blower to blow off any dust that settle on the panel protector as well as the camera LCD panel
• Remove the outer protective liner of the adhesive and align the panel protector in place with the camera LCD panel
• Apply pressure on the panel protector and leave the adhesive for approximate minutes to ensure maximum secure of the panel protector to the camera LCD panel
• Peel off the protective liner on the panel protector (with the scratch resistant able) and clean the surface with microfibre cloth

How to Clean an LCD Protector:

• Remove the protector from your device. Hold the protector under a stream of warm water in order to rinse it
• Apply one or two squirts of hand soap from a pump dispenser to the damp protector
• Hold the protector under a slow stream of warm water and then use your fingertips to gently rub the soapy mixture over the protector, removing any dust or other accumulation of dirt
• Rinse the protector again, holding it under a stream of warm water. Continue to rinse until all traces of soap are removed and the water runs clear
• Take the protector to a room or environment which is as free from dust as possible. Air-dry it by swinging it through the air vigorously until it has dried
• Reapply the completely dry protector to your electronic device

Tips & Warnings:

• Perform the adhesive process in a steamy bathroom to ensure there is no dust on the LCD

NOTE:

• Use a thin plastic business card or similar item (the plastic package of this protector could be used as the tool) to slide around the edge of the screen to remove it
• Do not pull or use fingernails to lift the four corners of the screen protector as it may break the glass protector, hurt your fingers and/or damage the camera

Package Included:

• 1 x LCD Panel Protector for Canon 5D