CCTV Portable 2.5Inch 30Fps Car Camera Vehicle DVR INS-CARPD01

Specifications:

• Video Resolution: 1280 x 720,30fps
• Main Function: Video, take picture, shift detection, usb, pc camera
• Support: Time set, preview and delete file
• Video Format: AVI
• Video Coding: JPG
• Image Pixels: 8M pix
• Video Resolution: 1280 x 720
• Video Frame Rate: 30fps
• Picture Format: JPG
• Image Ratio: 16:9
• Charging Voltage: DC-5V
• Interface Type: Min5 pin usb
• Storage Support: TF card
• Loop Recording Time: 2 minutes/5 minutes/15 minutes
• Battery Type: High-capacity polymer lithium battery
• Play Software: Operating system comes with video player software of mainstream
• Support System: Windows me/2000/XP/2003/vista, Mac os, Linux

Details:

• Features 1280 x 720 video resolution, the portable car camera DVR provides HD pictures

• The portable car camera DVR is with video, take picture, shift detection, usb, pc camera functions

• High quality material makes the portable car camera DVR durable and reliable for long time use

• With the bracket, easy to install the car rear view camera in your car

• With all the cables here, it is easy to set up and use the portable car camera DVR

Size in Detail:



Basic Structure:

How to Install a Rear-View Camera in Your Car:

• Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts
• Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal
• Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out
• Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight
• Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse
• Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions
• Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you

How to Build an in Car Camera Mount:

• step one is to determine the distance between the two metal bars on your head rest and measure their diameter once you have those measurements you can mark the holes on your piece of pipe and drill
• now you have your mounting points and can determine how long you will need the piece of pipe to be
• mount the piece of pipe with the head rest and use your tape measure to determine the distance where you will mount your camera on the pipe then add and extra 1/2 inch or full inch and mark it on the pipe this will be your cutting mark
• remove the pipe from the head rest
• now simply use a saw to cut your pipe on the mark you made
• for this step i recommend that you have a certain seat angle and that you know what it is every time you film because this camera mount is not adjustable and when the angle of your seat changes the camera will not be filming at the same point
• so determine the angle of your seat and mark the hole as perfectly as you can and drill to the diameter of the screw you bought to fit the camera
• now you have completed your camera mount a simple D.I.Y. the last thing to do is put it all together inside the car so simply mount it on the head-rest and screw the camera on now take a test drive and see how well you made it

Package Included:

• 1 x Dual camera traffic recorder
• 1 x Bracket
• 2 x USB Cable
• 1 x Car Adapter