Brightness Colorful Angel LED Decorative Light with USB

Specifications:

• Compact size, LED Decorative Light is easy to carry of the lovely decorative light
• This LED Decorative Light is safe and environmental friendly
• Lovely LED Decorative Light is ideal for decorating homes
• Brightness LED Light is made of high quality material with great individual care and attention to detail
• USB LED Light adds a decoration and softly illuminate to bedroom
• A great way to add decorative lighting effects to your stage, displays or home decorative
• Power: 0.5 W
• Power Voltage:3.5 V
• Bulb Material: LED
• Long Life: 60000 hours
• Lamp String Length: 1.5m

Details:

• Compact size, easy to carry of the lovely decorative light. Lovely LED Decorative Light is ideal for decorating homes

• This decorative light is safe and environmental friendly. USB LED Light adds a decoration and softly illuminate to bedroom

• Brightness LED Light is made of high quality material with great individual care and attention to detail

• A great way to add decorative lighting effects to your stage, displays or home decorative

How to Replace a LED Light:



LED lights are more energy efficient light solutions for holiday decorations as they require less power and produce a more focused, direct light when compared to standard incandescent strings. Many people are making the switch from standard Christmas lights to LED lights as the available technology to produce them gets better and the cost is lower, but it's surprising to find that LED bulbs can have problems that mimic their incandescent counterparts. Light strings have been observed to fail about three bulbs per week, so it's important to pick up a replacement string of lights when buying LEDs

Replacing a Bulb

• Plug in the LED lights to identify any low light emitting or dark bulbs. Place a small length of string or a twist tie around the wire near the bulb to help in finding it once the string is unplugged
• Unplug the lights. Pull out the faulty bulbs by gently grasping them and pulling them straight out away from the socket. Use care to not crush the bulb as you pull it
• Replace with a new bulb from a different string, or from the replacement pack. Push the bulb into the socket gently, and it should snap into place
• Plug in the string of lights to ensure that the replacement bulb is glowing and that the connection is good. Remove the marker string from the wires

Replacing a Fuse

• If the entire string of lights does not work, it's time to check the LED fuse. Locate the fuse box on the plug; it will be on the side of the plug and have a small door attached. Open the door using a small screwdriver or butter knife
• Pull out the small burnt fuse and inspect the damage. Check under and around the fuse in the plug for melted plastic; in extreme power surges, fuses can fracture and cause damage to the housing of the plug. Do not use lights that have melted the casing of the fuse. Use care to avoid crushing the fuse, as fuses are made of glass
• Snap a new fuse into the fuse compartment by pushing on it slightly with your fingertip. Close the fuse box
• Plug the lights in to test the new fuse; if the string of lights do not light up when plugged in, check the fuse again to make sure it's making good contact

How to Install LED Lighting:

LED lighting is a newer way to provide light to various places, such as under a kitchen cabinet. This type of light is typically more energy efficient than a standard incandescent light. Depending on how your cabinets are built the lights are designed to have a low profile so they cannot be seen under the cabinet. Installing LED lights can be done by first deciding where to place the LED light assembly

• Mark the placement for the LED lights so that so you know where the electrical wiring needs to be located
• Find a place for the electrical source for the LED lights. The electrical source is typically located within a kitchen cabinet
• Drill small pilot holes in the underside of the cabinet to see where the wiring will need to go
• Locate a circuit to use for the LED lighting on your home's junction or circuit box
• Turn off the circuit that is going to be used for the LED lighting
• Feed the electrical wire from your basement junction or circuit box, through the floor, up to the cabinet
• Connect the electrical wire from the lighting source to the LED lighting. Refer to the LED lighting instructions to properly connect the electrical wiring
• Connect the ground wires from the electrical source for the LED lights to the switch box
• Turn on the circuit from the junction box and test the lighting by turning the light switch to the "on" position

Tips & Warnings:

• LEDs produce much less heat than standard holiday lights, and use about 1/10th of the energy. The technology available for creating these lights is still improving
• If the dim or burnt lights do not easily come out of their sockets, it's possible that the lights have been made to prevent replacing the bulbs. In these cases, bulb replacement would damage the light string, so it's best to discard these lights when the majority have gone out

Package Included:

• 1 x LED Decorative Light