Digital LCD Auto Range Display Multimeter DT-830N

Specifications:

• Input Impedance: 10MΩ
• DC Voltage: 400mV/4V/40V/400V/600V / ± (0.8% +1)
• AC Voltage: 4V/40V/400V/600V ± (1.2% +5)
• AC Current: 400A/1000A ± (1.5% +5)
• Resistance: 400Ω/4kΩ/40kΩ/400kΩ/4MΩ/40MΩ ±(1%+2)
• Capacitance: 40nF/400nF/4mF/40mF/200mF ± (3% +5)
• Frequency: 10Hz-10MHz ± (0.1% +3)
• The Biggest Show: 3999
• Operating Environment: 0°C~40°C, under <75% R.H.
• Storage Environment: -10°C~50°C, under <80% R.H.
• Display Size: 52 x 27mm/2.04 x 1.06in
• Size: 260 x 104 x 52mm/10.23 x  4.09 x 2.04in

Features:

• Clamp on Pocket Digital Multimeter AMP test tester designed for use by electricians, technicians, serviceman and hobbists who required an instrument that is accurate,reliable, and always ready for use
• Pocket Digital Multimeter with data hold function
• LCD display with automatic polarity indication
• Uses one 9V battery

Details:

• With pocket size, the Handheld Digital Multimeter is ideal for hobby & technical operations

• The Best Digital Multimeter will test DC voltage, AC voltage, DC current, AC current, resistance, capacitance

• The pocket digital multimeter is a battery-powered, average responding-rms indicating multimeter

Size in Detail:

How to Measure Electrical Components Using a Multimeter:

• A multimeter is a common device used to troubleshoot and measure the properties of electricity in components, such as voltage, current and impedance/resistance. Learning to correctly use a multimeter allows you to troubleshoot delicate electronic components by determining how electricity is flowing through them. You need to know how to use the two probes and when to have current flowing through a device you intend to measure

Measuring Voltage:

• Turn on the device to be measured
• Set the multimeter to either VDC or VAC. This indicates whether you're testing direct current (DC) voltage or alternating current (AC) voltage
• Plug the red wire into the positive socket on the multimeter and the black wire into the negative. According to Science Buddies Electronics Primer, the negative socket is marked with "COM" for "common" and the positive socket is marked with "V" for "voltage
• Touch the positive lead to the terminal of the device that has a positive voltage and the negative lead to the negatively-charged terminal. This applies when testing DC. When testing AC, there is no positive or negative voltage. You'll be able to determine whether you have the leads connected properly by looking at the measurement; if the voltage reading on the multimeter is negative, switch the leads

Measuring Resistance:

• Switch the multimeter reading to ohms to detect resistance
• Turn off power to the appliance or component you intend to measure
• Touch the leads to opposite sides of the component at electrical contact points or wires, so electricity can flow through the component and the meter can measure resistance

Measuring Current:

• Set the multimeter to read amperage
• Turn off power to the component and break the circuit by removing a wire from its connection point
• Plug the black lead into the negative socket, marked "COM," and the red lead into one of the amperage sockets. According to the Northwestern University website, multimeters typically have sockets rated at 300 mA and 10 A, or 300 milliamps and 10 amps. Always plug the red lead into the 10 A socket until you're sure that the current is less than 300 mA
• Connect your leads to the open ends of the circuit to reclose the circuit. Turn the power on and get your reading
• Turn the power off and reconnect the original circuit

Package Included:

• 1 x Digital Multimeter
• 2 x Tester Leads