Customers Also Bought
Spec Equipment Remote control
- A 2.4GHz 6EX 6CH transmitter and receiver set
- No same frequency interference
- The helicopter remote control is with low power consumption
- High sensitivity, easy to use
- R606FS high sensitivity receiver weighs only 0.25oz (7g) without case yet is a full range system for all aircraft from giant scale to Park Flyer applications-no need to buy separate receiver for specific aircraft rubber grommets installed where antennas exit to eliminate stress and fraying of the wires
- Dual antenna diversity enables FASST system to automatically and seamlessly select the best reception between the two antennas built into the receiver ensuring that the aircraft stays under constant control of transmitter regardless of altitude
Pre-Vision Packet Screening technology scans incoming data for potential problems and applies sophisticated error correction techniques for solid impenetrable link with model
- Easy Link system features a unique ID code in the transmitter that links to the receiver insuring that receiver only follows commands from this transmitter-with over 134 million possible codes there is no chance for a conflict
- No hassle Fail Safe programmed through transmitter-no complicated set-up steps or binding plugs
- When performing a ground check, the Power Down function allows modeler to reduce power from up to 50+ paces away-like retracting the antenna on a conventional transmitter
- Purpose built custom IC chips for key functions, no off-the-shelf IC chips
- Transmitter Color: Black & Silver
- Transmitter Material: Metal & Plastic
- The first look at the transmitter Receiver Set
- Fine details design
- Features different channels for easy use
- The antenna details
- The whole accessories of the Transmitter Receiver Set
- With all the cables here, the 6CH transmitter receiver set is easy to use
- Before you are enjoy the flight, the preflight adjustments will helps you reduces a lot of problem while your RC helicopter flying in the sky
- Always check all the controls to make sure they move in the correct direction and here is no mechanical binding or noise from the servos
Hovering is when the RC helicopter is floating in a stationary position in the air. Hovering is the fundamental maneuver to learn first. Here is the procedure to practice hovering
- (1): Make sure there are no spectators anywhere near the RC model helicopter. You, the pilot, should stand at least 10 meters (30 feet) behind and slightly to the side of the RC heli
- (2): Prior to lifting off, while the main rotor is spinning and the RC helicopter is on the ground, check the main rotor fore/aft and left/right cyclic to make sure the main rotor is tilting in the correct direction according to your cyclic command. Move the tail rotor control stick to make sure the RC helicopter nose will swing in the desired direction
- (3): Increase the throttle/collective to lift he model RC helicopter skids off the ground to no more than 10cm (4 inches). Initially, it will be very difficult to control the RC helicopter to prevent it from moving. For a beginner it will also be difficult to determine whether the RC helicopter is in trim or not. But with repeated practice close to the ground you will develop a feel for the controls. It is recommended to let a more experienced model helicopter pilot trim out your new RC helicopter before you attempt to learn to hover
It will take a few hours of hover practice with the helicopter skids at 10 to 20 cm (4-8 inches) off the ground in order to comfortably control the model
- (1): Do not try to lift the RC helicopter to more than 10 to 20 cm (4-8 inches) in the beginning because then the model may tip over readily when the beginner panics and an incorrect command is given. Once you can keep the model in one place, then it is time to slowly increase the height by a few centimeters (inches) each flight. Soon, you will be able to hover the RC helicopter confidently a few feet high. Beginners should always practice hovering close to the ground because in an emergency, throttle and collective can be reduced rapidly without causing a large drop or damage to the RC helicopter. If the RC helicopter is hovering beyond one meter (3 feet) altitude, always descend slowly. A panic drop can damage the helicopter
- (2): Always stand behind the RC model helicopter when learning how to hover. Then you can watch the nose of the RC helicopter. A left tail rotor command will yaw the RC helicopter nose to the left, and a right command will yaw to the right. Similarly, a left cyclic command will cause the RC helicopter to translate left. After you can comfortably hover the model at one meter high without drifting, then start practice hovering while standing to either side of the model. Eventually, you need to be comfortable at hover the RC helicopter from any orientation, including with the RC helicopter nose pointing at you. This is challenging because control directions are reversed
- (3): Once you can confidently hover a RC model helicopter at any altitude and at any orientation, then congratulate yourself because you have mastered 80% of the fundamental control movements of a helicopter
Foward Flight Training:
- (1): Start practicing moving the helicopter laterally to the left or right slowly from a 1.5 meter (60inches) high hover. This is the beginning exercise of translational flight
- (2): After a few hours of practicing step (1) and you are comfortable with translational movement, start using some tail rotor control so the helicopter nose will point slightly to the left or right as you fly it to the left or right. Eventually, this pattern will become a figure-eight in front of you. Please visualize these movements in your mind
- Buy a Flight Simulator such as the Real Flight G2 simulator. A Pentium IV PC is more than enough. Flight simulators allow you the luxury of crashing without the danger and expense
- Use training landing gears to enlarge your helicopter footprint, making it easier to make safe landings
- Have an experienced helicopter flyer teach you how! Look for a local club or flying field and talk to the experts. Or ask your local hobby shop owner... the good ones will really help you out
- Recharge it again before the power is off. Otherwise, it would be damaged dramatically, even resulting that you can never recharge it again
- Please do not touch, when the motor rotates in high speed and the battery is charging
- 1 x Transmitter
- 1 x Receiver
- 1 x 9.6V/600mAh Battery
- 1 x Adapter
If the order has not been shipped; please contact DinoDirect Live Support for order cancellation.You will get your refund within 24 hours.
If the order has already been shipped; you may return the item to us postmarked within 30 calendar days of delivery. Before that, please contact our Live Support to inform that.
In that case we will refund you the payment excluding actual shipping fees already incurred.
If the item is defective, please contact DinoDirect Live Support and send an email to us at firstname.lastname@example.org attached an image or video file clearly showing the defect of the product. And we will give you a response within 24 hours whether we will resend the item or refund the payment to you for compensation.
For customization, please consider carefully before ordering.Because we do not accept return and replacement.
|Unit Price||USD$ 222.65||USD$ 219.11||USD$ 215.57||USD$ 210.85|
|Enter Wholesale Channel>>|
• If the order has not been shipped; please contact DinoDirect Live Support for order cancellation.You will get your refund within 24 hours.
• If the order has already been shipped; you may return the item to us postmarked within 30 calendar days of delivery. Please contact our Live Support to inform that.
• Please contact Live Chat or click here to learn more return policy.