High-definition Licence Plate Night Vision Waterproof Camera

Specifications:

• Image Device: Color CMOS
• TV System: PAL/NTSC
• IP Rating: IP68
• Effective Pixels: 628 x 586 pixels/510 x 496 pixels
• Resolution: 420 TV lines
• Lens Angle: 135 degree
• Power Supply: DC 12V
• Size: 250 x 30 x 40mm / 9.8 x 1.18 x 1.57in (L x W x T)

Features:

• High-definition and wide viewing angles
• View Angle can be adjusted
• New infrared LED'S night vision
• Licence Plate Night Vision Car Camera, High-definition and wide viewing angles
• This HD Car Camera is suitable for guard and security
• This Waterproof Car Camera can be used both in car and home
• This Night Vision Car Camera is perfect solution to get rid of poor rear view visibility on your car, boat, trailer, camper, truck, or any vehicle that has no rear-view mirror or poor rear vision
• This Night Vision Car Camera can be connected to any type of monitor such as your in-car DVD player, media player, navigation system w/ video support, or TFT rear view mirror using a composite yellow RCA jack for crystal clear resolution 

Details:

• New infrared LED'S night vision 
• Licence Plate Night Vision Car Camera, High-definition and wide viewing angles

• This Night Vision Car Camera can be connected to any type of monitor such as your in-car DVD player, media player, navigation system w/ video support, or TFT rear view mirror using a composite yellow RCA jack for crystal clear resolution 

• Easy to install and use 
• This HD Car Camera is suitable for guard and security
• This Waterproof Car Camera can be used both in car and home

• This Night Vision Car Camera is perfect solution to get rid of poor rear view visibility on your car, boat, trailer, camper, truck, or any vehicle that has no rear-view mirror or poor rear vision

Size in Detail:

How to Install a Night Vision Camera in Your Car:

• Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts
• Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal
• Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out
• Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight
• Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse
• Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions
• Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you

How to Build a Car Camera Mount

Shooting stable video from inside a moving car is very difficult without some sort of camera mount. Professional car mounts sold by grip equipment houses and professional camera stores can easily cost more than $1,000, and are out of the price range of many independent filmmakers and amateur photographers. Using some basic hardware and a little ingenuity, however, you can make your own car camera mount that should be able to hold most small and medium-sized cameras. With this mount, you can station a camera in the rear of the cab, pointing it out to the front windshield and driver.

• Drill a 3/8-inch between the edge and the center hole of a metal electrical plate. This will be used to mount the ball head to the plate.
• Pass the 3/8-inch bolt (with 16 threads per inch) through the hole you just drilled and hold it into place using a nut.
• Place the two wide washers on either side of the metal plate over the center hole, sandwiching the smaller washer from underneath the plate.
• Remove the bolt that will hold a child safety seat from the back seat of the car. Remove the plastic housing surrounding the bolt, and bolt the metal plate in its place.
• Screw the ball head into the 3/8-inch 16 bolt and then level and attach a camera.

Package Included:

• 1 x Licence Plate Waterproof Camera
• 1 x Power Line
• 1 x AV Cable