![tcl [The genuine original] TCL21 "flat screen monitor MC21 2-way video 2 audio](http://p.lefux.com/61/20130520/T0001ASUWQ/the-genuine-original-tcl21-quot-flat-screen-monitor-mc21-2-w-0-small.jpg)
-
-
Specifications:
- Beam Angle: 60degree
- Wavelength: 850nm
- Compatible with: Camera lens
- Dimension: 109mm / 4.3in (Outer Diameter) ; 33.5mm / 1.32in (Inner Diameter) ; 14mm / 0.6in (H)
- Voltage: DC 12V
Features:
- 72 IR LED board for CCTV security cameras
- This LED Illuminator Board Plate has very bright infrared 60 LEDs without much energy consume, and it is easy to use
- The Infrared Illuminator Board Plate features excellent detail and realism
- Very bright infrared LEDs without much energy consume
- A replaceable LED board for your broken or worn out IR LED board
- This Professional Camera Illuminator Board Plate is just for your CCTV security camera
Details:
- This LED Illuminator Board Plate has very bright infrared 60 LEDs without much energy consume, and it is easy to use
- Alao the LED Illuminator Board Plate is brighter than regular LED bulbs and it has wider field of view
- With accurate design
- Back view of the infrared LED illuminator board plate
- Built-in auto protection circuit against damaging the illuminator board plate by high voltage
How to Make Flashing LED Circuit Board?
A fun hobby for electronic enthusiasts is making a flashing LED circuit board. You can use a flashing LED circuit board with other projects such as making flashing signs or billboards or building toys, robots, or Christmas decorations. Electronics manufacturers use LED indicators, such as those you see in servers, computers and network hardware. There are flashing LED kits available in the market, but you can also make your own so that you can create the pattern as elaborate as you want it to be.
- Design a schematic diagram of your LED circuit board on your computer. You can use Adobe Photoshop or MS Paint to create your diagram. It should show the locations for the LED output, LED lights, ohm resistors, 9-volt battery and clip as well as the 555 timer. For a sample of LED flashing circuit design, see Resources below.
- Print your design using a laserjet printer. Use a photo basic gloss paper to print your diagram. Cut it to the actual size of the schematic diagram.
- Tape the printed photo paper on the perfboard. Cut the perfboad to size using the photo paper as your guide.
- Remove the photo paper and then rough up the surface of the perfboard using steel wool. Use the steel wool to even out the edges of the perfboard. Wear a respiratory mask to prevent inhaling the toxic dust from copper.
- Use a hot iron to transfer the printed design from the basic photo gloss paper to the perfboard. The plastic of the printer toner should stick onto the perfboard.
- Remove the paper by soaking under water for a few minutes and then peeling it off to reveal the transferred design.
- Etch the print on the perfboard. Dip the perfboard in a container filled with ferric chlorine purchased from the electronic store. Wear rubber gloves to prevent the stain from sticking to your hands. Agitate the container to submerge the perfboard inside the container. Ensure that the solution covers the perfboard completely. Leave it there for about 20 minutes. Constantly check and dip in a container with water to see if the copper is gone. Dip in solution again if the perfboard still has copper.
- Use acetone to wipe clean the surface of the perfboard and remove any remaining ferric chlorine.
- Drill holes into the perfboard based on the design where your LED lights will go. Use a drill press and 0.0350 etch carbide drill bit to make the right size holes.
- Solder the parts using your diagram as your guide. Connect the positive to a negative of the LED wire connectors. Connect the UF capacitor, which will determine the speed of the blinking LED. You can choose from 10 to 1000 UF capacitor. Choose the one that would work well for your project. Connect the 9V battery to the battery clip then you are done.
Package Included:
- 1 x 60Degree Infrared 72LED Illuminator Board Plate for CCTV Security Camera with Regulator Board
Get DinoPoint™ by Writing reviews, Post Images, or Post Videos. The first five customers can get double points!
Haley Crow
from ()
Bought this item on
05-21-2011- Other Thoughts: My dad loves this gift. <br/> <br/>Program whatever you want onto the plate and roll around town. Very visable. Just be careful that you dont get a ticket. It can be illegal in some states.
Was this review helpful?
Patricia Dake
from ()
Bought this item on
05-16-2011- Other Thoughts: A little difficult to get the hang of programming, but once over that, it is fun to use, and it gets attention. Changing messages is fairly easy. It could use a mirror feature, so that it could be used on the front. I like it, I have one on all my cars, including a rarely street driven autocross and rally car.
Was this review helpful?
Illuminator Board Plate
from ()
Bought this item on
05-04-2011- Other Thoughts: If it were easier to program I'd give this a full 5 stars. But, hey, it's cheap and it works great. I actually poked the LED screen out of the frame and use it by itself in one of my hotrods. It's compact and you can mount it anywhere. What is especially nice is that, once you program it, the message stays in memory even after power is removed. This is a big plus because. . . .
Was this review helpful?
Denise Vander Wall
from ()
Bought this item on
05-06-2011- Other Thoughts: I ordered a led scrolling license plate and I am very satisfied with my purchase. I ordered it and received it in within 4 days, i was told that i would not recieve this item for about two weeks, but i recieved it way before then.
Was this review helpful?
Douglas G. Phillips
from ()
Bought this item on
05-27-2011- Other Thoughts: Works great just like it says and helps spread the message of Ron Paul!
Was this review helpful?
Maybe you are interested in:
