LCD Monitor Screen Protector Cover for Nikon D70 BM-4

Specifications:

• Brand new MASSA LCD Monitor Cover for Nikon D70 BM-4
• Made of high quality plastic material
• Fit your Nikon D70 BM-4 snugly
• Very easy to apply
• Protect the camera screen well
• This is an original product
• Dimension: 66 x 52mm / 2.6 x 2.0in (L x W)

Details:

• Monitor Screen Protector for Nikon protects your LCD screen from scratch and is brand new LCD monitor cover for Nikon D70

• Your LCD screen will be protected against harmful impact with the high quality and lightweight Monitor Screen protector

• Nice and lightweight Nikon screen protector is made of high quality and durable plastic material

• Plastic screen protector can be easily clip onto the back of the camera and can be easily removed at any time

Size in Detail:



How to Clean an LCD Protector?

• Remove the protector from your device. Hold the protector under a stream of warm water in order to rinse it
• Apply one or two squirts of hand soap from a pump dispenser to the damp protector
• Hold the protector under a slow stream of warm water and then use your fingertips to gently rub the soapy mixture over the protector, removing any dust or other accumulation of dirt
• Rinse the protector again, holding it under a stream of warm water. Continue to rinse until all traces of soap are removed and the water runs clear
• Take the protector to a room or environment which is as free from dust as possible. Air-dry it by swinging it through the air vigorously until it has dried
• Reapply the completely dry protector to your electronic device

How to Apply A Screen Protector To A Camera' LCD Monitor:

• Clean the surface of the LCD monitor with the cleaning tissue that comes in most protector packages
• Hold the acetate against the LCD screen and determine how it needs to be cut down to fit over the monitor screen. Trim the acetate so that it is slightly smaller than the area to be covered so you avoid ragged edges of the acetate hanging over off the screen
• Carefully peel the paper backing off the acetate
• Start at the right side of the monitor and apply the acetate
• Lay the camera on a table up against a book or something to hold it in place
• Hold the acetate in your left hand and touch the lower right hand corner of the monitor with one corner of the acetate. Let the protector fall along the right side of the screen and once it is vertically aligned with the monitor gently press it in place with a finger on your right hand
• Gently press the screen protector into place
• Using a credit card (or the pressure card that comes with some screen protectors and starting on the right side of the screen protector apply a firm and consistent pressure to the forward edge of the card and slowly push it along, flattening the screen protector as you go
• Watch for air bubbles and as you press the credit card forward try to push any bubbles ahead of the card and off the screen
• Once you've pressed down the entire screen protector use a thumb to push any air bubbles toward the nearest edge and off the monitor
• Run a finger around the edge of the acetate pressing it firmly against the edge of the LCD monitor.
• Don't worry if you can't get all the bubbles out. A few very small ones won't affect your monitor view

How to Install a Screen Protector:

• Protecting a liquid crystal display on electronic equipment or a laptop is important ensure permanent damage does not occur to a delicate LCD. Installing protective film can be tricky because if the screen is not completely clean, dirt will be trapped beneath the screen protector. Additionally, if care is not taken to adhere the protector, it might not go on smoothly and without wrinkles

Instructions for Attaching a Screen Protector:

• Because many electronics devices have liquid crystal display screens, screen protectors have grown in popularity. To keep an LCD screen clean and avoid scratching the fragile surface, you should cover it with a clear screen protector. The screen protector adheres directly to the LCD screen and covers it entirely. With the screen protector in place, you can then relax and stop worrying about permanent scratches in the LCD screens of your electronic devices

Important:

• Please note that one side of the LCD panel protector had anti-scratch coating as indicated by the label, The other side has been silkscreen according to the LCD panel and therefore does not have anti-scratch coating

Installation:

• Remove the protective liner from the silkscreen side
• Gently clean the exposed panel protector side with the protector liner removed with a clean microfibre cloth. Be careful not to apply too much strength as residue on the microfibre cloth may cause any scratches as this side does not have anti-scratch coating.
• Measure cut and paste the supplied adhesive according to the black silkscreen area.
• Clean the camera LCD panel to remove dust or tiny residue
• Use a blower to blow off any dust that settle on the panel protector as well as the camera LCD panel
• Remove the outer protective liner of the adhesive and align the panel protector in place with the camera LCD panel
• Apply pressure on the panel protector and leave the adhesive for approximate minutes to ensure maximum secure of the panel protector to the camera LCD panel
• Peel off the protective liner on the panel protector (with the scratch resistant able) and clean the surface with microfibre cloth

Tips & Warnings:

• Perform the adhesive process in a steamy bathroom to ensure there is no dust on the LCD

Package Included:

• 1 x LCD Monitor Screen Protector Cover for Nikon D70