-
-
Specifications:
- This Brushless Governor Motor is made of special material
- This Brushless Governor Motor is low-maintenance, unique design for this Motor for RC Helicopter
- Three point battery type and low voltage selection
- Software reversion of motor turning direction
- This Cheap Brushless Speed Control Governor Motor used in aircraft and helicopter installations
- Simple setup, no complicated switches or wiring
- This Brushless Governor Motor and speed controls are designed for great performance in your airplanes
- Tough surface mount construction
- Safe power on function
- Current: 5A
- BEC: Max. 1A
- Size: 38 x 20 x 6mm / 1.5 x 0.8 x 0.2in(L x W x H)
Details:
- This Brushless Governor Motor is made of special material
- Three point battery type and low voltage selection
- This Brushless Governor Motor is low-maintenance, unique design for this Motor for RC Helicopter
- This Cheap Brushless Speed Control Governor Motor used in aircraft and helicopter installations
- Simple setup, no complicated switches or wiring
- Software reversion of motor turning direction
How to Make Homemade RC Helicopters
Flying RC helicopter is really very exhilarating. Their versatility gives a RC pilot a complete access to the three-dimensional space in such a way that no other machines can! I have played RC helicopter for more than one year but still find that I have just learnt a few tricks that it can perform.
There are generally two micro-helicopters ( indoor ) in the RC market. I have already planned to buy one of them as they can fly inside the living room and even take off on ours hand. Unlike those operated by gas, these electric helicopters are very clean and give out no terrible noise at all. In one nightfall, I visited a web site, which is about how to make a hand made RC helicopter. I was totally impressed and started designing my own helicopter. Here is my helicopter:
Instructions:
- The plan of the helicopter had finally been completed. It is not very well drew. The current plan available is only for the fixed pitch design. Please click the above photo for the plan.
- Making the main body
- The material that I use to make the main body of the helicopter would make you feel surprise. It is the circuit board ( after removing the copper layer ) that purchased from electronic shops. It is made of a kind of fiber which gives abnormal strength to it
- Would you think it is just too simple? Well, it is really a very simple design as the tail rotor is powered by a separate motor. This eliminates the needs not to construct a complicated power transfer unit from the main motor to the tail. The tail boom is simply fixed on the main body by 2 screws together with some epoxy adhesive
- Make sure that the aluminum ball placed in the rod end can be moved freely. 2 holes were drilled on the plastic spacer in order to house two screws that used to hold the ball linkage
- In my design, the swashplate is fixed on the main shaft. This is simply done by applying some glue between the aluminum ball and the shaft
- My instructions are too confusing? Here is my draft of the swashplate which might help you. I still find that my design is a little bit too complex. If you have a better design, please let me know!
- For the rotor head, I choose the same material as the main body - the circuit board. First of all, I have to claim that the rotor head must be sturdy enough to withstand any vibration or it could be very dangerous.The control system I used here is the Hiller system. In this simple control system, the cyclic controls are transmitted from the servos to the flybar only and the main blade cyclic pitch is controlled by the flybar tilt only
- There is a metal bar ironed perpendicularly to the flybar. It holds the metal ball of the ball link in position. Here is how the ball link is made
- The rob ends are shortened and a metal bar is used to connected them together. the metal bar should be inserted deep into the rob ends and fixed with epoxy adhesive
- In addition to the ball link, an "H" shaped anti-rotating unit is a must for the control system. It helps to keep the ball link in position. The materials needed are showed in the above photo.(19)
- In order to stop the lower part of the swashplate from moving, an anti-rotation unit is also needed here. It is simple a small board with two pins inserted on it
- Here is the measurement of the tail blade. It can be shaped easily from a 2mm thick balsa. the tail blades make an angle of ~9°on the blade holder
- The photo shows all the things that the tail part consists. The two balsa blades are hold by a hardwood holder which helps to give a fixed tail pitch. It is then secured on the gearwheel by 2 screws. The motor is simply glued on the tail boom by epoxy adhesive and the tail shaft holding tube with the same way on the motor.The tail blade is made of balsa. They are covered with heat shrink tube in order to reduce the friction between the blade and the air.The pitch and the weight of the two blades must be exactly the same. Tests must be performed to ensure that no vibration occur
- Only two servos are used in my design. One is for the elevator and the other one is for aileron. In my design, the aileron servo is installed between the motor and the main shift holding tube. In this way, the tube has made use of the sturdy plastic case of the servo as one of its supporting medium
- This arrangement gives extra strength to the main shift holding tube as one side of the servo is glued to the motor while the other side is glued to the tube. However, the mobility of the servo as well as the motor is lost
- In a fixed pitch design, only 2 servos are needed.A computerized Tx is needed as the the tail control must be mixed with the throttle control. For a Piccolo micro helicopter, this task is performed by the Piccoboard. For my design, this is done by the function "Revo-Mixing" in the Tx
- now you can play with your home made heli.... enjoy it
Package Included:
- 1 x ESC Speed Governor
Get DinoPoint™ by Writing reviews, Post Images, or Post Videos. The first five customers can get double points!
B. Simpson
from ()
Bought this item on
06-09-2011- Other Thoughts: This a very good Brushless Speed Control Governor Motor for the price. I fly two of them now with no issues at all.
Was this review helpful?
JOSE SANTOS CARDOSO
from ()
Bought this item on
06-01-2011- Other Thoughts: She's still flying like brand new. No issues so far with this Brushless Speed Control Governor Motor.
Was this review helpful?
Nicole Rhodes
from ()
Bought this item on
04-03-2011- Other Thoughts: Makes a great place to store your old esc and motor after swapping it with this brushless kit. I'm very pleased and would absolutly buy over and over if i had more cars to convert to brushless!
Was this review helpful?
Horacio Correa
from ()
Bought this item on
04-15-2011- Other Thoughts: As for packaging and delivery,delivered great on time no damage or anything,i cant complain.
Was this review helpful?
Kimberly Trouy
from ()
Bought this item on
05-17-2011- Other Thoughts: It's actually rather scary going so fast. You crash at that speed and you'll break something. In fact I broke my Right Aluminum Turnbuckle on the first day.
Was this review helpful?
Maybe you are interested in:
