Customers Also Bought
Spec Brand Pixel
2.4GHz High-speed 2-ways communication system
Transmitter Stand-by Time
1000hrs (CR-2 lithium-ion battery)
Receiver Stand-by Time
500hrs (CR-2 lithium-ion battery)
63 X 38 X 30 mm/2.48 x 1.50 x 1.18in(L x W x H)
70 X 38 x 30mm/2.76 x 1.50 x 1.18in(L x W x H)
- New and high quality
- TR-331 uses a global free FSK 2.4GHz wireless channels, 15 selectable channels
- The maximum control distances up to 65 meter
- Use the LCD to display channel, power, and functional mode
- Ultra-low power consumption for standby; the standby time of TR-331 TX transmitter is more than 1000 hours, the TR-331 RX receiver standby time is more than 500 hours
- Simultaneously control multiple flash or studio lights
- Support for flash's auto-focus feature
- Support a variety of shutter speeds, its max up to 1/8000s
- Through the PC socket controls the studio lights and other brands flash with PC interface
- This is a remote flash trigger for Nikon which simultaneously controls multiple flash or studio lights
- The maximum control distances of the wireless flash trigger is up to 65 meter
- This remote flash trigger for Nikon is designeed with a battery jar for you to put battery in
- This TR-331 remote flash trigger uses a global free FSK 2.4GHz wireless channels with 15 selectable channels
- This Nikon flash trigger for Nikon is packed in an elegant paper card
How to Trigger Flashes on Professional Cameras?
- The most characteristic element of photography is probably the flash. Perhaps it's the sound or maybe it's the spots you see afterward. But for some reason the flash takes us instantly to thoughts of cameras. There are several different ways to implement a flash with a professional camera
- Assess the scene to determine what kind of flash will be appropriate to use. The type of flash means how big the flash needs to be and how far from the camera you want it. There is a link to a helpful table below. Another factor for your flash will be your ability to use camera equipment such as a tripod or an umbrella stand
- Lock the flash directly into the flash port of your camera. This technique is for the highest amount of mobility and is probably the easiest flash set up to pull off. All you need is you camera and the flash. When you take the picture, the flash will automatically trigger
- Attach a bracket to your camera to give your flash a little more height and distance from the lens. This technique has its advantages, but it also requires more equipment such as the bracket itself and a short cord that will attach the flash to the flash port on your camera. The flash will deploy automatically when you take the picture
- Hook the flash to your camera with a much longer cord and mount the flash independently. As you venture into more professional looking photos, the brightness and distance of the flash is going to vary depending on your subject. This technique will require a separate stand for your flash, a much longer cord to connect to your camera, and a tripod to stabilize the camera itself. Once again, the flash will automatically fire when you take the picture
- Connect your flash to the camera via a wireless system. This is essentially another variation of step four, only there are no cords involved to trip people up or to prohibit flash placement. This is good for high traffic areas or shoots with particularly odd environments. These wireless systems can be bought for various prices which may determine the quality of their performance
How to Check the Flash Trigger Voltage?
- Checking the trigger voltage on a flash camera or strobe device serves an important function for the user-owner. Manufacturers set maximum strobe voltages, which keep the units within safe voltage tolerances. Some infrared and regular strobes use high voltages for mechanical cameras, but many of the newer digital models can be permanently damaged by higher voltages. Some models can tolerate very high voltages, but such information can be attributed to rumor and optimistic guesswork. The best solution is for you to find the exact voltage requirements from a certified source and check the voltage with a multimeter for your brand and model unit
- Refer to your operator's manual for the specifications data on strobe voltage. You will find the manufacture's listing for the maximum operating strobe voltage for your brand and model. It will be indicated in volts, such as 3.5, 6 or 10 volts. Keep that number in mind. If you have no owner's manual, log on to a site such as Botzilla.com, where you can find the specification chart on strobe voltages for your make and model
- Disconnect your strobe flash from the camera and install new batteries in the compartment. Unsnap the flash case and place the required number and type of batteries inside the battery bed, with the positive (+) poles of the batteries matching the positive poles in the flash unit. Snap the case back on
- Charge the flash until the "Ready" light or LED comes on, or until a green or other active signal is recognized that indicates flash charging. Look at the bottom of the flash connector configuration, called the "hotshoe." It will have pins protruding from the connector flange. Some flashes have a male-female connector similar to a coaxial cable fitting, while others have a central "hot" pin with a conductor element next to it or on the side. Check your manual to be sure
- Set a 10 ohm or higher digital multimeter for the lowest or most sensitive volts scale, which might be from 0 to 20 volts. Place the red positive meter lead on the center pin of the hotshoe. In the case of a PC-type connector, place the red lead on the central metal pin. The hot lead will always be centered in the circular or rectangular shoe, no matter what brand and model camera you have
- Place the negative (-) black lead of the multimeter on the element connector, located next to the central pin on some models, or on the side of the shoe. For hard to reach element connections, use a paperclip to probe the connector and rest it on the negative lead. If you make a mistake, or receive no volt reading, switch your contacts points -- it will not harm the flash unit
- Read the volts indicated on the meter. They should match your specification voltage from the chart or your owner's manual. You can adjust the multimeter for a finer reading with extra decimals, if you wish to get the most accurate voltage. Instead of a reading of 3.5 volts, set the sensitivity higher, which will indicate something like 3.578 volts
- 1 x Remote Flash Trigger for Nikon
If the order has not been shipped; please contact DinoDirect Live Support for order cancellation.You will get your refund within 24 hours.
If the order has already been shipped; you may return the item to us postmarked within 30 calendar days of delivery. Before that, please contact our Live Support to inform that.
In that case we will refund you the payment excluding actual shipping fees already incurred.
If the item is defective, please contact DinoDirect Live Support and send an email to us at firstname.lastname@example.org attached an image or video file clearly showing the defect of the product. And we will give you a response within 24 hours whether we will resend the item or refund the payment to you for compensation.
For customization, please consider carefully before ordering.Because we do not accept return and replacement.
|Unit Price||USD$ 139.20||USD$ 136.05||USD$ 132.89||USD$ 128.69|
|Enter Wholesale Channel>>|
• If the order has not been shipped; please contact DinoDirect Live Support for order cancellation.You will get your refund within 24 hours.
• If the order has already been shipped; you may return the item to us postmarked within 30 calendar days of delivery. Please contact our Live Support to inform that.
• Please contact Live Chat or click here to learn more return policy.