-
-
Specifications:
- Efficient value charger charges up to four AA 2500mAh Ni-MH rechargeable batteries at once
- For AA nickel-chloride battery, 1-4 battery arbitrary charge
- SANGER with nickel-metal hydride (Ni-MH) batteries, rechargeable up to 1000 times, more convenient and economical
- By switching power supply technology (high-frequency pulse transformer red), superior performance, lightweight and reliable
- Built-in folding plug, portable and beautiful
- When battery is charging, the LED light is red, extinguish after the battery is full
- Nickel-metal hydride (Ni-MH) batteries do not contain mercury cadmium
- Renewable and reusable, Ni-MH Rechargeable Batteries are a good economic and environmental choice
- Suitable for Camera, Walkman, CD, PDA, video games, MP3 and so on
- Using high quality materials, low power, small temperature rise
- Convenient and compact, perfect for the family road trips and the photographer on the go
- Charger Input: AC 100V-240V 50/60Hz 120mA Max
- Charger Output: 1.4V-250mA ± 50mA
- Charging Time: 16 hours
- Capacity: 2500mAh
Details:

- High performance, especially if high discharge currents are required (like in Digital cameras) cheap in use, because they can be recharged many times
How to Make a AA Battery Charger:
- Rechargeable AA batteries are an increasingly common product and are useful for someone who uses a lot of batteries in such devices as portable audio players, cameras, flashlights and battery-powered toys. Here's a design for a battery charger that can be made out of simple materials and only costs a few dollars in parts. You can use it to charge your AA batteries or nearly any other type or rechargeable battery as well
Instructions:
- Cut three lengths of wire. Cut two pieces that are six inches long, and one single piece that is 10 inches long. Once you've cut the wire to length, strip the insulation from the ends of the wire so that each end of each wire has about one to one and a half inches of bare wire exposed
- Take the wire lead from the silicon diode (See "Resources" below) and wrap it around one of the screw connections on the bottom of the light bulb base. Tighten the screw connection with a screwdriver. Take one of the 6-inch wires and wrap one of the bare ends around the second wire lead of the diode. Wrap electrical tape around the joint
- Twist together the bare end of the other 6-inch wire to one of the leads of the electric plug. Cover the joint with electrical tape. Wrap the other end of the 6-inch wire to the second screw connector on the bottom of the light bulb base and tighten with a screwdriver
- Twist together an end of the 10-inch wire and the other lead of the plug. Wrap the joint with electrical tape to cover the bare wires
- Put the light bulb base onto the piece of wood and fasten down with wood screws. Screw a 60-watt bulb into the light bulb base
- To charge your AA battery, tape the two bare wires of the charger onto the battery's ends -- one to the negative, and one to the positive. This should be the wire connected to the light bulb, not the electrical plug. Plug the charger's electrical plug into a wall socket. The charger works slowly, so allow it to operate for two to four hours and then check the charge of your battery by putting it in your device and testing it
Package Included:
- 1 x Power Charger
- 4 x AA 2500mAh Ni-MH Rechargeable Batteries
Get DinoPoint™ by Writing reviews, Post Images, or Post Videos. The first five customers can get double points!











![Tian Qiu [Sale] AG3 button batteries new Generation III ag3 LR41 392A, said remote control toys spreadsheets 192](http://p.lefux.com/61//hosting/61/20130619/T00020XOAW/r41-392a-said-remote-control-toys-spreadsheets-192-p14289285-1small.jpg)


![Tian Qiu [Genuine guarantee] hardcover celestial AG3 392A 384 LR41 button batteries](http://p.lefux.com/61//hosting/61/20130619/T00020XOGE/cover-celestial-ag3-392a-384-lr41-button-batteries-p14289423-1small.jpg)








































