-
-
Specifications:
- Made of high quality material
- You can gather your card file
- Business card file combines business card holder into a single unit
- Business card file is a good decoration to embellish your desk
- A sleek and compact storage solution that keeps your cards clean, undamaged
- Business card file is a perfect gift for someone special or treats for you
- It is high-grade atmospheric with vogue leather
- It has a id a and two card slot
- Size: 10.5 x 7x 1.6cm/4.13x 2.76x 0.63in
- Colour: Black
- Material: Leather
Details:

- This leather business card holder is high-grade atmospheric with vogue leather

- Business card file is a good decoration to embellish your desk
- The surface of business card file is simple designed and can combine business card holder into a single unit

- Unique and elegant exterior is attractive of this leather business card holder

- Business card file is also a perfect gift for someone special or treats for you
How to Make a Business Card Holder?

In today's world, business cards are a must for the professional, the self promoter, and the convenience of
swapping an address.There are many different types of business card holders on the market, but with a few minutes of your time and a little creativity - you can make a business card holder that is uniquely your own
Instructions:
Choose a trendy or plain designed fabric of your liking. Dig through some scrap material left over from other projects, or if you are going to your local fabric outlet pick up a fat quarter.Some fabric outlets have various size pieces already cut or left over from the bolt they roll up and sell at discount pricesDrawing Pattern
- Create your pattern. You will need a piece of paper, ruler, and a pencil
- Measure a rectangle 4 inches wide by 9 inches long and cut out
- Fold your paper rectangle in three equal parts
Curved lines
- At one end of a third take a can good and curve both edges and trim curved edge with paper
- Pin pattern to fabric and cut. You will need two pieces of fabric and one piece of fusible interfacing
- Fuse interfacing to wrong side of one piece of fabric. Make sure you place the interfacing shiny side down on the fabric
Sewing
- Right sides together stitch around fabric leaving a 1 - 2 inch opening at the bottom.
- Turn right side out, stitch closed opening, and press with hot iron
Folded Fabric
- Fold fabric in thirds. Pin bottom section in place to hold and stitch down both sides.
- Using a sew on snap place one side of snap in middle of bottom portion of business card holder and stitch in place.
- Stitch the other half of snap onto the inside of top flap in position to connect with the bottom portion of snap.(You can substitute Velcro for the snap if you want.)
- Next time someone wants your business card you'll not only have them available, but in your very own stylish card holder
How to Design a Business Card Holder?

Business cards are one of the most effective ways to advertise your business. They cost little to produce, they're easy to carry and they provide a way for prospective clients to contact you. For a place to store your business cards at your office, make a business card holder from scratch. It's another way to save money while promoting your businessInstructions:
- Cut a piece of wax paper 1 foot long. This will serve as your work area because the wax won't allow things to stick to it.
- Lay two craft sticks flat on the wax paper, side by side. Use strong glue to glue them together to form the base of the cardholder.
- Glue four craft sticks together the same way to form the back of the cardholder. Stand the piece upright and apply glue along the bottom edge of the bottom stick. Press the glued edge against the base piece of the cardholder.
- Lay three craft sticks side by side and glue them together to form the front of the cardholder. Repeat the process in step 3 to glue the piece to the base of the cardholder.
- Use scissors to cut 1.25 inches off either end of two craft sticks. Discard the middle sections. Lay the remaining pieces side by side and glue them together in two pairs. Apply glue along the bottom edge of each pair and press it against the base of the cardholder to form the left and right sides.
- Let the glue on the business card holder dry. Fill it with business cards
Package Included:
- 1 x Business Card File Holder
Get DinoPoint™ by Writing reviews, Post Images, or Post Videos. The first five customers can get double points!
Kathrine
from ()
Bought this item on
12-05-2011- Other Thoughts: I like the appearance of the business card file, and I believe my husband will like it
Was this review helpful?
Burne.Jones
from ()
Bought this item on
12-04-2011- Other Thoughts: Fast delivery than I expected! Excellent details make the business card file more elegant!
Was this review helpful?
Carlos J. Duncan
from ()
Bought this item on
12-06-2011- Other Thoughts: This business card file has low price and high quality. It makes me so happy!
Was this review helpful?
Alejandro
from ()
Bought this item on
12-07-2011- Other Thoughts: This business card file is really useful for me to collect the business card well
Was this review helpful?
Jacqueline
from ()
Bought this item on
12-03-2011- Other Thoughts: My husband likes the business card holder very much. He was so happy with this gift.
Was this review helpful?
Maybe you are interested in:



















![DeLi [Special] red crown Deli (Deli) 9175 - Metal textured black Pen Multifunctional Office Block](http://p.lefux.com/61/20130523/T0001HEYOV/special-red-crown-deli-deli-9175-metal-textured-black-pen-mu-1-small.jpg)


































