DSLRKIT DC-04 4 Channel Wireless Studio Flash Trigger

Specifications:

• Channel Frequency: FM 433MHz
• Effective Distance: 30m
• Sync Speed: 1/500S
• Transmitter Power Source: 12V/23A
• Receiver Power Source: AAA Battery
• Size: 80 x 34 x 18mm / 3.1 x 1.3 x 0.7in (L x W x H)

Features:

• The remote trigger for studio flashes and outdoor flash is used as the controller of synchronous trigger studio flash of cameras
• It consists of a signal sender and a receiver trigger and works by means of the frequency modulation wireless remote control
• The signal transmitter adopts the advanced circuit and components, and can transmit the coded FM wireless signal
• The circuit of the transmitter has the function of standby and hibernation, thus it has low power consumption
• The product adopts micro-computer for controlling the decoding, Which has superior anti-interference capability; sensitive reaction speed, the distance can reach 30m and the highest synchronous speed can reach 1/500 sec

Details:

• The wireless remote trigger is designed for camera synchronizer studio and on-location work to trigger various flash lights

• This Remote Flash Trigger with high quality and totally new brand. No more dangling with sync cord. This wireless remote trigger fits most cameras

• This Remote Flash Trigger with high quality and totally new brand. No more dangling with sync cord. This wireless remote trigger fits most cameras

• With this high quality wireless remote trigger, you can catch the most beautiful most beautiful moments. This Camera Remote Trigger is the best choice for traveler with camera

Size in Detail:

Precautions:

• Always use the appropriate battery
• Use new battery when the old battery is powerless and the transmitter stops running
• Prevent it from dropping or colliding with hare things
• Check the flash lights trigger mode carefully before use
• Flash leak phenomenon possibly happens if there is any other electric wave at the place 

How to Make a Trigger for a Crossbow:

• Use the wood chisel to cut a rectangle 1 inch wide by 1 1/2 inch through the crossbow stock (top to bottom) at the point you wish to mount the trigger
• Using the drill and 3/8-inch wood bit, drill a hole through the center of the round side of the hardwood cylinder
• Using the narrow blade wood saw for the rough cut and the chisel for finishing, cut notches for the bow string and trigger into the hardwood cylinder as shown in the drawing
• Using the drill and 3/8-inch wood bit, drill a hole through the sides of the crossbow stock to mount the trigger block as shown in the drawing. Slip one of the metal rods, 3/8 inch by 6 inches, through as the trigger block pivot
• Using the drill and 3/16 inch metal bit, drill two holes in each of the 3-inch long metal straps: one being 1/4 inch from one end, the second being 1 inch down from the first and both being in the center of the width of the straps. Using the 3/8-inch metal bit, drill a third hole 5/8 inch from the other end of the strap and centered
• Clamp the 5-inch strap of metal in the bench vise with the last 3/4 inch of one end held in the jaws. Bend the strap so the last 3/4 inch is 90 degrees to the rest of the strap
• Epoxy the remaining 3/8 inch metal rod to the 5-inch metal strap at a point no more than 1 1/2 inches back from the 90 degree bend and perpendicular to the length of the strap. Allow epoxy to harden completely. If you have access to welding equipment, welding this pivot arm would be better.
• Fit the angled end of the 5-inch trigger bar into the bottom of the trigger block (see drawing from step 4). Use this positioning to determine the best point to mount the smaller straps to the crossbow stock (using the wood screws) to allow the 3/8-inch holes cut in the straps to hold the trigger pivot out at a comfortable distance from the stock. When a string is pulling against the trigger block, the trigger bar must hold the block in place. To release the string (fire the crossbow), the archer will squeeze the trigger bar up (from a grip behind the trigger pivot) which will pull the trigger bar down and out of the trigger block notch. This must be a smooth and comfortable action for the archer to ensure the best results

Package Included:

• 1 x Transmitter
• 1 x Receiver
• 1 x PC Sync Cord
• 1 x Plug